Lasko H20685 Use and Care Manual download pdf (Page 2)

Rev. C 11/14

H20685ES

Rev. C 11/14

H20685ES

MODELO H20685

ENSAMBLAJE DE LA BASE DE SOPORTE Y LA

CAJA DE CONTROL (Figuras 1 y 2)

LA CAJA DEL CONTROL DEL VENTILADOR DEBE SER

MONTADA AL SOPORTE ANTES DE UTILIZAR EL VENTILADOR.

1. Cuidadosamente retire el Ventilador de la bolsa plástica y la caja.

2. Alinee los dos lados del ventilador con el soporte (Figura 1). Al

presionar los botones del soporte, empújelos hasta que queden

fijos en su lugar.

ADVERTENCIA: Los tacos de plástico o hule, tales como

las patas de esta unidad, pueden pegarse a la superficie de los

muebles. La unidad podría dejar un residuo capaz de oscurecer,

manchar o dejar marcas permanentes en el acabado de ciertas

superficies de muebles, incluyendo superficies y pisos de madera.

3. Remover el tornillo de sujeción de la parte trasera de la caja

de control del ventilador.(Vea Figura 2)

4. Asegurarse de que el alambre de la caja de control del

ventilador al motor está entre la parta del pedestal y la

rejilla tal como se muestra.

5. Insertar el tornillo de sujeción de la parte trasera del ventilador

a travez del orificio en la pata del pedestal tal como se muestra.

(Figura 2)

6. Alinear la caja de control del ventilador con el

tornillo de sujeción.

7. Apretar el tornillo de sujeción con la mano. No lo

aprete demasiado.

8. Conecte el cable eléctrico a un tomacorriente de 120 V.

Asegúrese que el enchufe encaje firmemente en el

tomacorriente.

Cuando los enchufes quedan flojos en los

tomacorrientes, pueden deslizarse parcial o

completamente fuera del tomacorriente con un leve

movimiento del cable adosado. Los tomacorrientes

en este estado podrían sobrecalentarse y representar

un grave peligro de incendio; si está cubierto por una

cortina o tela, el riesgo de incendio es aún mayor.

9. Presione el botón de Encendido

( ) para encender el ventilador.

Seleccionar la velocidad deseada pulsando el botón de

velocidad (

10. Para ajustar el ángulo vertical, mueva el cuerpo del Ventilador

hacia delante o hacia atrás hasta la posición deseada.

QUICKMOUNT

DEL SOPORTE PARA LA PARED

1. Escoja una ubicación que monta que permitirá la instalación de

hardware (no suministró) directamente en sementales de pared

ni apoyo estructural adecuado.

2. Utilizar el paréntesis de pared como una plantilla, marca las ubi-

caciones de hoyo en la pared después de nivelar el paréntesis.

3. Abroche paréntesis de pared a montar superficie que utiliza 2

cierres calibrados apropiados. Taladre hoyos pilotos como sea

necesario. (Vea la Figura 3).

El CUIDADO: Verifique para eléctrico y/o las líneas de gas antes

de instalar el paréntesis de pared.

COLGANDO EL VENTILADOR EN EL SOPORTE

PARA LA PARED

1. Sostenga el ventilador en una posición vertical, como si estuviera

sobre en el suelo.

2. Coloque el borde trasero del pedestal en los ganchos del soporte

para la pared.

Su ventilador puede ser armado en la pared usando el nuevo

soporte para la pared de montaje rápido suministrados

con su ventilador. (Figuras 3 y 4)

QUICKMOUNT

SYSTEM

Figura 3

Figura 2

Figura 4

Obtenga los sujetadores adecuados para montar este

Ventilador.

3. Permita que el pedestal gire hacia abajo de modo que los pies

de goma delanteros se apoyen en la pared debajo del soporte

de montaje.

4. Incline la cabeza del ventilador a la posición deseada.

Figura 1

Botón del

soporte

Botón del

soporte

VISTA DELANTERA

VISTA TRASERA

Caja de

control

la celebración

de tornillo

Gire la perilla

exterior de

las agujas

del reloj para

apretar

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Fan.

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS

FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:

DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,

gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the con-

tainers for these products!

ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet

and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition

should be replaced by a qualified electrician.

ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means

of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan

when not in use.

BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.

The Blue Plug™ on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed

or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper

with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.

The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no

circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be

replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and

all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.

DO NOT USE A THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE THE RISK OF ELEC-

TRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.

• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these

devices may overheat and cause a fire hazard.

•DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire

hazard.

•ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.

•NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.

•DO NOT block, cover or obstruct air flow to or from the fan while in operation.

•DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location

may create a shock hazard.

•DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture

or appliances. Arrange cord away from traffic area and where it will not be tripped over.

•NEVER use a single extension cord to operate more than one Fan or other electrical device.

•DO NOT use this Fan if it has been damaged or is not functioning properly.

•Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,

move the Fan to another location.

•Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.

•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural

facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article

547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.

•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous

locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical

requirements for hazardous locations.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu-

lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient

or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the

user’s authority to operate this equipment.

CAUTION

1 2 3 4

Comments to this Manuals

No comments

Lasko H20685 Use and Care Manual Page 2

Comments to this Manuals

Related products and manuals for Household fans Lasko H20685